Lian Li Lancool Mesh II Performance
Born to push the limits
LANCOOL II MESH Performance features a mesh front panel and mesh bottom left shroud panel, honeycomb vent design and built-in PWM fans, ensuring bountiful airflow delivered to your components while the system runs at peak performance.
THE ULTIMATE CHASSIS FOR BEGINNERS AND ENTHUSIASTS ALIKE
EXQUISITE STEEL CRAFTSMANSHIP
Mesh intakes spanning the front panel guarantee sufficient airflow in and out of the system, allowing it to run at peak performance.
MORE ADVANCED COOLING SUPPORT
Optimized airflow is a result of the collaboration between the brand-new mesh design, additional exhaust vent holes, and three high-performance PWM cooling fans.
MESH FRONT PANEL
MESH BOTTOM LEFT SHROUD PANEL
HIGH-PERFORMANCE BUILT-IN PWM FANS
2 x 140mm PWM intake fans pre-installed at the front and 1 x 120mm exhaust fan in the back of the PERFORMANCE EDITION produce ample airflow, keeping your system running at peak performance.
Front: 2 x 140mm PWM fans
140mm PWM fans
- RPM range: 600~1200 RPM
- Static pressure: 1.49mmH2O (maximum)
- Airflow: 60.56 CFM (maximum)
Back: 1 x 120mm PWM fans
120mm PWM fans
- RPM range: 600~1500 RPM
- Static pressure: 1.78mmH2O (maximum)
- Airflow: 54.6 CFM (maximum)
EXPERIENCE FAN CONTROL ON A WHOLE NEW LEVEL
The four-mode fan controller on the top front allows you to experience fan control on a whole new level. Select L for casual use like internet browsing, press H when you’re pushing your GPU(s) and CPU hard.
The included hub supports up to 6 PWM fans with either 3-PIN or 4-PIN headers.
Note! The hub supports fans with either 3-PIN or 4-PIN header. However, if you intend to synchronize and control fan speed and noise level for the added fans via the fan controller, the added fans should have 4-PIN PWM headers.
MODULAR PSU SHROUD COVER
The space between the top and bottom chamber now features two removable PSU shroud covers to house either 2 x 2.5” SSDs or can be removed to fit 2 x 120mm fans.
Compared to the former integrated design, the modular PSU shroud covers allow users to remove them for an unobstructed airflow between the top and bottom chamber.
When 2 fans are mounted, and the cover plates removed, ventilation efficiency is even better.
Even when 2 x SSDs are mounted, the vents on the PSU shroud covers guarantee good ventilation.
MULTI-WAY FAN/RADIATOR BRACKET
The multi-way bracket revolutionizes your notion of fan/radiator installation by offering 4 installation options to best fit your needs.
Closer to the motherboard for more direct cooling
Closer to the front panel for thick radiators
HOW TO INSTALL THE MULTI-WAY FAN/RAD BRACKET
The multi-way bracket revolutionizes your notion of fan/radiator installation by offering 4 installation options to best fit your need.
Do not install a 140/280MM radiator in the inner side of the bracket otherwise irrepairable deformation might occur. The correct way to install is to mount fans first then place a radiator on top of the fans.
OPTIMIZED STORAGE CONFIGURATION
With the modular drive cage, side-mounted SSD bays, and additional SSD space on the modular PSU shroud cover, the LANCOOL II MESH is capable of holding up to 9 drives.
TOOLLESS SLIDING DRIVE CAGE
Slide the hard drive cage along its bottom track to the position that best fits your interior configuration.
DRIVE INSTALLATION GUIDE
SUPPORT UP TO 9 DRIVES
Modular drive cage: 3 x 3.5” HDDs/2.5” SSDs
Side-mounted SSD bays behind motherboard tray:
2 x 2.5” SSDs
Side-mounted SSD bays at the bottom right flip shroud:
2 x 2.5” SSDs
Vertical GPU Kit
Hot-swappable Back Plate
LANCOOLII-4X 3.1 Type C Cable
GB-001X Anti-sag GPU Bracket
In the condition of using the included riser cable (PCIE3.0) of the vertical GPU kit with a PCIE 4.0 motherboard and a PCIE 4.0 GPU, please follow bellow steps to set up your BIOS to make it compatible.
1.Make sure that your motherboard BIOS is the latest version. If not, recommend to update to the latest version.
2. Install your GPU directly to the motherboard and start.
3. Enter your BIOS, set the PCIE slot from “Auto” to “Gen 3”. (Example photo as below, for more please read the manual of your motherboard)
5. Install the PCIE 3.0 riser cable to the motherboard and the GPU, the system would be able to work.
|Model||LANCOOL II MESH PERFORMANCE|
|Dimensions||(D) 478mm x (W) 229mm x (H) 494mm|
|Motherboard||E-ATX(width: under 280mm)/ATX/M-ATX/ITX|
4.0mm tempered glass (both sides)
|Fan Support||Front: 2 x 140mm or 3 x 120mm
Top: 2 x 120mm or 2 x 140mm
Top of PSU chamber: 2 x 120mm
|Radiator||Front (multi-way fan/radiator bracket): 1 x 360/280/240mmTop: 1 x 240mm (aligned to the left)|
|Drive||Behind MB Tray: 2 x 2.5″ SSDBehind the right flip panel: 2 x 2.5”SSD
Hard Drive Cage: 3 x 3.5″ HDD/2.5″ SSD
Above PSU Chamber: 2 x 2.5″ SSD
|I/O Ports||1 x Fan speed control button1 x TRRS AUDIO
2 x USB 3.0
1 x USB 3.1 TYPEC
|Dust Filters||1 x Top (magnetic), 1 x Bottom (tray)|
|Incl Fans||2 x 140mm PWM Fan (front)
Rated Speed:600 ±200 (30% Duty)-1200RPM ±10%
Noise:25.8dB(A)1x 120mm PWM fan (rear)
Rated Speed:600 ±200 (30% Duty)-1500RPM ±10%